The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
The content which follows on the subject of How to Install a Bathtub Yourself is exceedingly engaging. Don't miss it.
Mounting a bathtub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging task. If the old tub is easily accessible, the project can move immediately; if you need to open up a wall surface to remove the old bathtub as well as position the new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the new one. Make certain you have actually qualified on your own for the task and are comfortable attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is far better to consider using one prior to you start. Chances are you might require an expert plumber to make tube connections.
This short article will help you set up a new tub in your bathroom if you have already bought a new tub and also don't need to change the setup of your previous water system pipelines.
Your devices and also material list must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the limited accessibility that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning during this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place between the tap and also the sink. Safeguard the tap in place with the manufacturer provided backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the needed position. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small points.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bath tub till the level reads degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water and examine all joints and also brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the tub has been utilized at least once as this will certainly settle it right into its final setting.
Getting ready for the Installation
First of all, the sustaining structure supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing issues with moisture and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can split relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Installing A Bathtub? Try leaving a remark down below. We will be interested to know your thoughts about this blog post. Hoping that you visit us again later on. Loved our piece of writing? Please share it. Let other people discover it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Address emergency plumbing promptly here. Report this page